The Fundamentals of Plumbing Knowledge for Bathtub Installation
The Fundamentals of Plumbing Knowledge for Bathtub Installation
Blog Article
This great article below about How to Install a Bathtub Yourself is pretty much entertaining. You should read it.
Installing a bath tub isn't precisely brain surgery, but it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a new one is also a moderately hard project. If the old bathtub is easily obtainable, the project can relocate immediately; if you need to open a wall to remove the old tub and position the brand-new tub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old bathtub as well as embeded in the new one. Make certain you have certified on your own for the job and are comfortable attempting it. Instead of working with a professional to take control of a halfway-completed project, it is far better to consider employing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your washroom if you have actually currently gotten a new tub and don't require to alter the arrangement of your previous supply of water pipes.
Your devices as well as material list need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Utilizing both wood boards under its feet, put the bathtub in the needed position. The wood boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub up until the level reads level.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the tub as well as likewise examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub should wait until the tub has been used a minimum of once as this will certainly resolve it into its final setting.
Preparing for the Setup
To start with, the sustaining structure provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, leading to problems with wetness and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also installations. They are sold in tubes as well as cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealer can crack fairly very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently readily available on the market. It is suggested to fit the floor tiles making use of waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that entry on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the web. If you enjoyed our page please don't forget to share it. Bless you for your time. Kindly pay a visit to our site back soon.
24-hour service? Dial here. Report this page